Descrizione con link .

Printing and Converting Sector

Brochure and attached documents:    
Printing & Converting  

Why Rimor?

The Printing sector uses essentially two methods of printing, flexo and offset.

Flexography is a method of direct rotary printing that uses a rubber pad arrays plates or photopolymer materials; the printing is direct: the cliché transfers ink directly to the substrate to be printed thanks to a slight pressure exerted by a pressure cylinder.

Offset printing is an indirect planographic printing process that is based on the chemical / physical phenomenon of repulsion between water and fatty substances.

The offset is a printing technique fundamentally based on the same principle of lithography. Instead of printing the sheet in direct contact with the stone or the microgranito aluminum plate, the printing is done through the use of three cylinders in contact with each other.

The converting system, it specializes in combining raw materials such as polyesters, adhesives, silicone, tapes, foams, plastic, felt, rubber, coatings and metals, as well as other materials, to create new products. Materials such as paper, film and strips are often produced in long, continuous forms that are rolled for handling and a more cost-effective transport.

Many processing companies draw rolls of large diameter, this increases the conversion efficiency, while minimizing the changes. At the end of the conversion process the rolls can be cut into smaller rolls on a cutting machine.

 

RECUBE

  • -50% EMISSION SURFACE
  • -50% SPACE OCCUPIED
  • NO JOINTS MAINTENANCE
  • LESS MOTORS MAINTENANCE (VERTICAL MOTORS)
  • RECUPERATOR ON BOARD
  • FLOW AND PRESSURE
    CONTROL ON BOARD

REDRYER

Example of flow diagram made by Rimor RECUBE system

VENTURI

    Compact monoblock Venturi system with:

  • BACKWARD-CURVED FAN
  • LARGE INLET CONE
  • BY-PASS VALVE WITH SET SCREW
  • REGULATION SYSTEM FOR VENTURI, WITH SET SCREW
  • SOUNDPROOFED SUCTION LINE
  • EXTRACTION CHAMBER FOR RETURNED AIR WITH PRECISION DRILLING

SOUNDPROOF CABIN

  • QUICK ASSEMBLY
  • CABIN WITH SINGLE BEAM STRUCTURE UP TO 10 M WITHOUT INTERNAL COLUMNS
  • MODULAR SYSTEM EXTENSIBLE
  • QUIPPED WITH LIGHT, VENTILATION, CLIMATE CONTROL, CRANES, DOORS, WINDOWS
  • CHANCE OF WALK-OVER AND/OR LOAD BEARING CEILING
  • VERSATILITY FOR SEVERAL USAGES
Vai a gestione rifili Vai a ricambistica Vai atrattamento aria di processo Vai a Linee complete forni con moduli Vai a depurazione ambienti Vai a moduli di ventilazione risparmio energetico Vai a Forni Vai a Servizi

 

 

The furnaces belonging to the sector printing and converting are used to dry the liquid part of paints (printing) and the adhesive supports or similar (converting). Rimor has got a special department within the sector able to face any kind of problem in matter of material, with solutions tested for years and provable results for power saving that reaches the 30%. The offer is completed by drives and systems for the process' control....
Back to Top
Rimor's fan units, that have been studied since 2005, are modern machines suitable and able to guarantee an important power saving and the highest performances. Rimor has  studied and realized machines installed at the top constructors with an important caliber of performances and endurances. ......
Back to Top
Helical fans,
Noiseless helical fans,
Extractor hoods....
Back to Top
The trims management and their shredding is nowadays an important process in order to recover the productivity of the system that produces plastic materials. Trims can be sucked with depression systems or under pressure (venturi). Two patents has been assigned to Rimor in the "innovation" and "efficiency" fields....
Back to "Venturi" 
The processed air is full of polluting agents like COV (volatile  organic compounds), or others, gaseous or fogs. The processed air could also contain solid particles (dusts)........
Back to Top
Thanks to a gained know how and to a technical highly qualified staff, Rimor is able to produce lines equipped with furnaces with modules, double-zero fans, batteries for the energy recovery, pipes, powerboards and probes. In that way Rimor  guarantees  high performances in order to gain the best result in matter of ventilation and construction of furnaces.  Drives,  control systems and processing  systems are also included in Rimor's production......
Back to Top
Rimor produces, thanks to the use of modern measuring systems and equipments:
- performance audits
-system's analysis with measurements at  seat
-performance definition of existing machines, in order to evaluating them for their efficiency in using. It's so possible to  intervene with an upgrade or the substitution of the machine with a more efficient one, more suitable for using....
Back to Top
The development and production of electromechanical components and areaulici and projects within the company over the years has allowed management of spare parts and assistance at a high level.
The Rimor has a full equipped rehearsal room for the Service to its Customers.....
Back to Top


Rimor S.r.l. - Head Office: Via Luigi Santagata, 43 Torino - P.I. 05395260010
Rimor Srl Contact About us Versione Italiana Brazil version